Messages

16

Model 1934 Pistol / Re: Mauser 1934 firing pin not disengaging trigger bar

« on: July 30, 2017, 11:58:17 AM »

Sorry for the late response:    Preface;  as noted above by B Mason, work with a good gunsmith if you are not familiar with working on firearms.

I purchased a WWII replacement magazine (expensive) in very excellent condition and little wear.  I tried out the new magazine.  Still same problem.  I would have to push up on the mag to get the firing pin to disengage the trigger bar.   

I then went through looking at the other parts and the "ejector & hold open catch" looked great without significant wear, and the "magazine catch" was seated properly in the ejector & hold open catch.   

I found some original parts on the internet (trigger bar and firing pin) which turned out to be relatively inexpensive in relation to the original magazine.  I replaced the trigger bar first, and the pistol has functioned perfectly without any further issues (including smooth disassembly). Comparing the two parts did not reveal any significant wear that would explain the difference.  But for what ever reason, the replaced trigger bar did the trick. 

The below listing outlines the parts mentioned and you can find the parts here, on Ebay or other sights such as gunbroker.com.

Numrich:

  https://www.gunpartscorp.com/Manufacturers/Mauser-33384/AutoPistols-37346/1934PocketPistol-35076.htm?results=40


Happy collecting, Steve

17

Model 1934 Pistol / Re: Mauser 1934 firing pin not disengaging trigger bar

« on: March 14, 2017, 12:25:16 AM »

the two other photos:

18

Model 1934 Pistol / Re: Mauser 1934 firing pin not disengaging trigger bar

« on: March 14, 2017, 12:22:48 AM »

Follow up:  Problem Solved!


I did find a gentleman out in the country who has been a gunsmith for the last 40+ yrs.  He loved the opportunity to check out this pistol (he has worked on many Mauser's but never a Mauser 1934) and was willing to problem solve with me.  We worked on it for about an hour, taking it apart and putting it back together, making sure that all the parts were original and functioning. 


In short, this turned out to be a worn magazine lip (or possibly the ejector/hold open catch maybe worn down). Pushing up on the magazine firmly into the magazine well, while pulling the trigger, actuated the trigger bar and released the striker consistently.   

Although this magazine looks to be in good condition, the upper lip does demonstrate wear on right side back corner where the magazine engages the hold open catch (see Photos).


QUESTION:  In order to make sure that it is a magazine issue, and not the hold open catch, I need to acquire a magazine without wear on the lips.  I have looked online and most of the WWII era mags look worn.   Are there any good after market brands or stores that anyone knows to purchase a Magazine?


Also, I hope this may help someone in the future that may have similar issue. 


Thanks, Steve
[/size]

19

Model 1934 Pistol / Re: Mauser 1934 firing pin not disengaging trigger bar

« on: March 10, 2017, 09:24:12 PM »

Thanks B Mason,

No worries.  Understand diagnosing over forum is challenging at best;  just appreciating a little guidance on where to look next as to possible issues others may have had with this particular pistol.


 Once the pistol did not fire at the range, i called the seller to see what he wanted to do (before opening it up, especially given that it was sold as a working pistol).  He offered the option of sending it back right then, or opening it up, cleaning it (he recommended just using some "WD-40 to loosen up the parts; thats what these old guns need sometimes") and if still doesnt work then send it back.   


I really like the pistol and its history, so am trying to get it working as a functional pistol.  I collect them but also fire them at the range (history held in the hand and used, as well as admired in the case or on the shelf)


Ive worked with period C96, and WWII P38, P08 Luger, HSc, and PPK's, and comfotable with these.   All challenginging pistols in their own rights in getting them functioning properly (usually spring or part issues) But this Mauser 1934 has a striker fire system that has posed a different type of challenge.   


My main thought, as you noted as a possibility, is whether parts were replaced (or possibly not matching to the pistol; 1914 or 1910 placed in this 1934).   


As you might have experienced, many gunsmiths are not familiar with these vintage pistols, and most times i send one in, they come back with more problems than when i started (i currently have had a PPK in 3 times and still not fixed properly).   Im not dinging the gunsmith, just explaining my experience and the challenges with these C&R's. People who relish in their complexity and simplicity are truely a much better source of information.


If you know of a good Mauser specialist around Portland Oregon that would be great.  I will look at the trigger bar/ striker relationship. 


Much appreciated

20

Model 1934 Pistol / Mauser 1934 firing pin not disengaging trigger bar

« on: March 10, 2017, 12:37:18 AM »

I purchased a Mauser 1934 that was reported to be mechanically functioning.  Unfortunately the firing pin is not disengaging from the trigger bar, allowing it to move forward to strike the primer.   The trigger clicks, the bar moves downward, but the firing pin doesn't disengage from the bar.  The is experienced with the pistol disassembled and the same functions are noted when it is assembled.


I tried to down load a video of the action, and so far has not downloaded successfully (so I took photos of specific parts).  If it doesn't, I can send it as an attachment in an email to help others see what I am experiencing (I have the pistol disassembled to show the moving parts (as long as this is allowed in this forum)


The seller has agreed to take it back, But I like the pistol and wish to see if I can resolve the problem and get it back into working order.  I am familiar with full disassembly, replacing springs (have a spring packet from Wolf Springs, but these did not resolve the issue, so replaced the original springs), appropriately lubricating and re-assembly.


Any help would be greatly appreciated. 


Thanks Steve

21

Model 1914 Pistol / Mauser 1934 markings Unusual

« on: February 07, 2017, 10:33:46 PM »

Mauser 1934 that I am considering purchasing has  "Germany" stamped in the slide.I have not seen this before;  Could someone enlighten me on the significance of this.

22

Model 1934 Pistol / Re: Mauser 1934 markings Unusual

« on: February 07, 2017, 02:25:58 AM »

sorry did not load all the photos

23

Model 1934 Pistol / Mauser 1934 markings Unusual

« on: February 07, 2017, 02:24:22 AM »

This Mauser 1934 that I am considering purchasing has  "Germany" stamped in the slide.
[/size][/color]
[/size]I have not seen this before;  Could someone enlighten me on the significance of this.[/color][/size]ignificanc[/color]

24

Model HSC Pistol / Re: Seeking WWII original Grips

« on: February 05, 2017, 09:04:09 PM »

That is where I have been looking, but thought there might be another search area;  Will keep checking and see if they show up.  Much appreciated.

25

Model HSC Pistol / Other Slide markings on WWII HSc

« on: February 05, 2017, 08:59:52 PM »

I have a WWII matching numbers HSc.  I am curious of regarding the other markings on the Slide  Photos attached:


Any input appreciated. 

26

Model HSC Pistol / Seeking WWII original Grips

« on: February 05, 2017, 08:17:07 PM »

This appears to be one of the most difficult searches that I have endeavored.  I have not been able to find unbroken, original WWII production wooden grips for sale. 


Could anyone lead me in a good direction.  Very much appreciated.