Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - brlefty

Pages: [1]
1
Thanks Warbird. I left the gun and mags with a pretty skilled vet this last week. He thoroughly cleaned the gun and attempted tweaking both mags. One was the odd one that came with the gun - curved floorplate, and a new Triple K.
Neither will feed the first round without racking twice. I do like the gun, but was still avoiding the purchase on an original mag until I know nothing else is wrong. Appreciate your assistance.

2
Hello. I hope it is ok for me to inquire if anyone is capable, or knows of, repair in this area. I do have 2 magazines that are working, but only with a maximum of 6 cartridges. I suspect there is part wear that needs attention and/or part replacement. Thanks for any reply.

3
Model HSC Pistol / Re: I need help with identification.
« on: February 18, 2017, 11:35:58 AM »
Hi again Warbird. Since I am now waiting for a proper mag I thought it was a good time to disassemble and clean. While watching a video the person 'racked' the slide with the hammer down and the safety off. My gun will not 'rack'. I suspect this may have something to do with the previous owner trying to use an improper magazine. I am not certain I am describing this situation properly. Suggestions, comments, thanks! 

4
Model HSC Pistol / Re: I need help with identification.
« on: February 12, 2017, 02:11:14 PM »
Hello again,
This exchange began in July of 2015 when my friend wanted to sell the gun. He changed his mind, but recently did sell to me with 2 other pistols.
Today I did attempt to fire, but it jammed, as you folks had cautioned. The floor plate is curved, which does not match up well with the gun, but I had to try. Any comments welcomed! Thanks.

5
Model HSC Pistol / Re: I need help with identification.
« on: July 07, 2015, 05:43:11 PM »
You guys are too good at this, but now I have learned enough in the last few days to be somewhat hooked on nuance!
How could you tell the magazine was wrong? If I was going to buy the right one I sure would not want to be duped.
Would I dare try to shoot with it 'as is'? 

Thanks again,
Brian

6
Model HSC Pistol / Re: I need help with identification.
« on: July 06, 2015, 07:22:43 PM »
Gents - I did understand the 7.65/32 cartridge situation, but I didn't follow the magazine subject - 1914 vs HSC - how do you tell apart?
Anyways - I attached a few more pics for your perusal. Thank u!

7
Model HSC Pistol / Re: I need help with identification.
« on: July 06, 2015, 05:10:19 PM »
There is no stamping or embossing anywhere on the holster.
Based on the condition of this pistol, which I would rate barely as good, would any of you hazard a guess at its value? I appreciate all the input, as I had no Mauser knowledge except what I have learned since yesterday!

8
Model HSC Pistol / Re: I need help with identification.
« on: July 05, 2015, 09:47:03 PM »
Hi pardt - I am having a heck of a time with my reply, but Thanks for trying to help me out! I have 5 shells that fit the mag, but don't know if they will load. On the base of the grip next to the mag release there is a k. When I disassembled I found the last 3 digits - 624, of the s/n in 2 places - inside the slide and on the machined part that holds the spring. 

9
Model HSC Pistol / Re: I need help with identification.
« on: July 05, 2015, 06:04:35 PM »
Hello warbird - thanks for your reply.
S/N 780624
The magazine does fit the gun, as I removed for the pic.
What pic(s) would you need?

10
Model HSC Pistol / I need help with identification.
« on: July 05, 2015, 04:37:44 PM »
Hello. I have a 7.65mm Mauser with serial 78xxxx. I think this is 1942 and considered Third Generation Army based on M135 marking. It has a little rust and worn grips with tattered holster. Could anyone advise if I am correct in my assumptions, and approximate value?
thank you!

Pages: [1]