Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - vlim

Pages: [1] 2 3 ... 22
1
Site Technical Help or Site Feedback / Re: Site has been hacked
« on: December 21, 2023, 07:53:15 AM »
We got a few spam accounts. I banned and cleaned up the spam posts.

2
Model 1910 Pistol / Re: 1910/14 magazine question
« on: September 17, 2023, 02:14:39 PM »
Looks like your spring itself is riding a little low, it may have been installed incorrectly. It needs to go higher up in the frame.

3
Model HSC Pistol / Re: HSc 380 Tritium sights
« on: September 17, 2023, 02:10:49 PM »
These are quite collectable.


If you want to butcher a HSc, I would recommend finding something else.

4
Model HSC Pistol / Re: Purchase aftermarket grips/magazines
« on: September 17, 2023, 02:09:29 PM »
Note that the wartime HSc has a disconnector that differs from the postwar version.


The wartime left grip requires a slot that clears the disconnector.

5
Model HSC Pistol / Re: Mauser Model HSc
« on: August 02, 2023, 11:50:40 AM »
Yours is a late WW2 version. April, 1945.

6
Model HSC Pistol / Re: Purchase aftermarket grips/magazines
« on: August 02, 2023, 11:45:14 AM »
They sometimes turn up on Ebay.

7
Model HSC Pistol / Re: HSc Production Chart
« on: May 01, 2023, 06:58:23 AM »
01.27627 would be late 1971, early 1972.
Over 50 years old today and collectable indeed.


756642 appears to have a military acceptance at the left side. The commercial proofs on the right side are Eagle/N ones. Military accepted HSc's are desirable and collectable.

8
Model HSC Pistol / Re: Newbie Question
« on: April 30, 2023, 09:08:29 AM »
A wartime HSc that has been given a new number somewhere down the line. Hard to tell who applied it and why.

9
Model HSC Pistol / Re: HSC 32acp Disconnector
« on: April 03, 2023, 08:00:27 AM »
With the left grip removed, just press the triggerbar back in place, make sure it is seated well.


Keep some pressure on it, from the side, while installing the grip panel again.


It is quite normal for that bar to come loose, as it is held under pressure both front and rear.


Normal field strip after shooting only requires removal of the slide from the frame.


Proper method:
Check the pistol is empty.
Close the slide.
Cock the hammer.
Put safety on safe.
Press the release button and take off the slide.
Remove barrel and spring from the slide.


No further disassembly is required.

10
Model HSC Pistol / Re: Mauser Model HSc
« on: March 21, 2023, 02:19:05 PM »
1976, most probably.

11
Model HSC Pistol / Re: Mauser Model HSc
« on: March 08, 2023, 02:30:08 PM »
It should be a .380. Made in 1972.

12
Model HSC Pistol / Re: Mauser HSc 7.65. mfg in 1970
« on: March 08, 2023, 02:28:35 PM »
Yes, that's normal.


Interarms imported a lot less .32's, so good catch.


13
Model HSC Pistol / Re: HSC Gun Research
« on: February 11, 2023, 08:03:21 AM »
Made in 1972. The first 2 digits 01 show it is a .380.


Value depends on the state of the gun and the presence of the original box, test target, magazines, manual, etc..


A search on sites like Gunbroker should produce an average sales value.

14
Model HSC Pistol / Re: HSc in nickel plate
« on: February 11, 2023, 08:00:31 AM »
Production year would be 1970.
Interarms offered the nickle plated version on the US market. These guns were FBM proofed (internal Mauser proof) and not commercially proofed for the German market, so they unfortunately have no proof dates.

15
Model HSC Pistol / Re: HSc Production Chart
« on: January 25, 2023, 01:00:34 PM »
Yours is a commercial example.

Pages: [1] 2 3 ... 22