Mauser Guns Collectors Forum

Pistols => Model HSC Pistol => Topic started by: donp326 on December 30, 2013, 08:09:35 AM

Title: New to me a Mauser HSc
Post by: donp326 on December 30, 2013, 08:09:35 AM
This is a  HSc i purchased from Scotty Benedict at Pre98.com.  It's a second variation blued with E/655 and E/N stamps and E/N on the right side of the slide the seems to be a little fuzzy. it's the same Eagle/N that is on the trigger guard.  I noticed this when I looking at it under higher magnification.


The HSC also has the Mauser Banner on the base of the bottom plate of the magazine.  The serial number is 734970.  The last three digits of the serial no. are electro penciled on the inside of the front of the slide and and in front of the chamber on the barrel, all matching.  The sight channel is checkered also.


(http://i1271.photobucket.com/albums/jj624/donp326/MauserHScleft.jpg) (http://s1271.photobucket.com/user/donp326/media/MauserHScleft.jpg.html)


(http://i1271.photobucket.com/albums/jj624/donp326/MauserHScRight.jpg) (http://s1271.photobucket.com/user/donp326/media/MauserHScRight.jpg.html)


(http://i1271.photobucket.com/albums/jj624/donp326/MauserHScleftEover655.jpg) (http://s1271.photobucket.com/user/donp326/media/MauserHScleftEover655.jpg.html)


(http://i1271.photobucket.com/albums/jj624/donp326/MauserHScRightEagleoverN.jpg) (http://s1271.photobucket.com/user/donp326/media/MauserHScRightEagleoverN.jpg.html)


(http://i1271.photobucket.com/albums/jj624/donp326/MauserHScSerialNumber.jpg) (http://s1271.photobucket.com/user/donp326/media/MauserHScSerialNumber.jpg.html)

(http://i1271.photobucket.com/albums/jj624/donp326/ATPrightsideofslide.jpg) (http://s1271.photobucket.com/user/donp326/media/ATPrightsideofslide.jpg.html)
Title: Re: New to me a Mauser HSc
Post by: jcorl on December 30, 2013, 11:32:45 AM
One of my favorite variations with that ATP!  Congratulations.
Title: Re: New to me a Mauser HSc
Post by: Warbird on December 30, 2013, 04:54:47 PM
By definition, only the 1st Variation has an ATP (Army Test Proof) and it is located next to the Hammer on the left side of the Frame.  I believe what you think is an ATP on the Slide is a typical Eagle/N Proof Mark - there are three, one each on the Frame, Slide, and Barrel.  Also, the last ATP marked HSc was serial number 715323 so your new acquisition is well beyond that number.
Title: Re: New to me a Mauser HSc
Post by: jcorl on December 30, 2013, 05:07:32 PM
I believe Warbird is correct again, as the expert.  I don't see the ATP marking on the tang in your photo.  Bummer! 
Title: Re: New to me a Mauser HSc
Post by: donp326 on December 30, 2013, 05:09:34 PM
I thought the ATP was at the barrel end of the slide, my error. But the e/N there looks very much like an over stamp army test proof errantly applied to the end of the right side of the barrel end.
Title: Re: New to me a Mauser HSc
Post by: donp326 on December 30, 2013, 05:14:49 PM
I believe Warbird is correct again, as the expert.  I don't see the ATP marking on the tang in your photo.  Bummer!

The picture is fuzzy at best at that place. But l did look at it magnified today see m other posts.
Title: Re: New to me a Mauser HSc
Post by: donp326 on December 30, 2013, 05:27:56 PM
Warbird do have this HSc in your database if not you have it here.
Title: Re: New to me a Mauser HSc
Post by: Warbird on December 31, 2013, 06:58:52 AM
Thanks for sharing, Don.  If you're interested, your 2nd Variation Army with Large Eagle/655 Acceptance Mark was produced in September 1941, just 10 months after HSc production began.  Congratulations!
Title: Re: New to me a Mauser HSc
Post by: donp326 on December 31, 2013, 09:48:56 AM
Thanks I am always interested in any of my pistols historys.  Thanks for the info on my HSc.
Title: Re: New to me a Mauser HSc
Post by: gebirg on January 05, 2014, 03:50:51 AM
Congratulations with that E/655 - never seen one in Norway!
Title: Re: New to me a Mauser HSc
Post by: donp326 on January 07, 2014, 09:45:04 PM
Hello anyone the grips on my HSc are kind of dry.  What could I use that would restore some moisture to the wood but would not damage the wood or the value?